About Me


Hi, I'm Justin Baker your host here at Moulding Installation. What can I tell you about mouldings that you don't already know? Well, a lot, I hope!! I've been in the construction business for years, mostly as a general, but now have downsized to just doing specialty projects. It's my feeling that certain specific niches need to be filled with information. And I'm just the guy to fill it. I hope you will take the time to read some cool articles and enjoy the photos. And if you have a question or comment, I'll be happy to reply. Have a great day!!

Posts Tagged ‘cove molding’

How to Install Cove Moulding

Cove moulding has a hollow or inwardly rounded design and is used to beautify a room when installed horizontally at the seam where the wall and the ceiling come together. It is also made use of in order to conceal any flaws, joints or detail problems at the intersection where the wall and ceiling converge. Standard miter cuts are suitable for installation in most rooms. You may have need of a helper to assist you with holding the boards in place during the installation process and to keep the boards straight. Cove moulding can be purchased at most hardware and home improvement stores. Even though many people believe that a professional must be hired in order to perform the cove moulding installation, it is, in actuality, a very simple and easy process that can be carried out as long as you have the right tools.

Firstly, measure each and every wall in the room where you plan to install the cove moulding in order to ascertain the length of pieces you will require. Note down these dimensions. If possible, a single piece of cove moulding should be used for each wall. Leave an extra 10% of the total length for waste to your measurements.

Next, purchase the cove moulding at a local hardware or home improvement store. Cove moulding is available in a number of different types of wood and can be purchased in vinyl and plastic forms as well.

Cut the pieces of cove moulding as per your requirements. It is essential to remember not to cut the pieces too short. If you make use of a miter saw to trim the cove moulding, you must use at least a 60 tooth blade in order to make the cuts.

Locate the wall studs with the help of a pencil. You can then pre-drill your cove moulding at each and every wall stud in order to avoid splitting of the cove moulding during the installation process.

Apply any finish or paint to the cove moulding before installing it to the walls. This will allow you to apply the polish quicker and will also enable you to rectify any mistakes later with much ease.

Hold the piece of cove moulding in place and then nail them to the walls. Make use of a nail set in order to drive in the nails and avoid denting or damaging the cove moulding. As mentioned earlier, having two people help you during the installation process would make the process considerably easier seeing as cove moulding can be difficult to hold in place when cut into long pieces.

Incoming search terms:

  • cove moulding
  • cove molding installation
  • how to meet two peices of cove molding at two different angles
  • Inside Mitre Cut
  • install cove molding where 2 walls meet
  • installing cove molding
  • installing vinyl cove moulding
  • installingcovetrim
  • joint cove molding
  • miter tough angles for detail moldings

How to Cut Cove Molding

Most wood moldings are added against a flat wall or backing. However, there are certain types of moldings that are placed on the inside corner of a room where the piece of wood will be installed resting against two surfaces that converge at a 90 degree angle. Cove molding is one such type of molding that you will commonly find stretched around the perimeter of a room where the ceiling meets the wall. Even though cutting cove molding is slightly different from cutting most other types of molding, cutting cove molding is a fairly simple and easy task. In this article, we will learn how to cut cove molding.

To begin with, measure your room and purchase a few long pieces of cove molding that stretches from one corner to the other. Cut the molding for a splice connecting two pieces that converge in the center of a wall. This is the easiest cut to make and all you need to do is adjust the saw at a 45 degree angle and then push the cove molding into an even position alongside the back wall of the miter saw. Next, the cut is made by pushing the wood firmly against the backside of the saw. Remember to change the angle or reverse the next piece of cove molding in order that the back shows instead of the front while making the second cut for the splice. In this manner, each piece will fit into the splice with the two angles pointed in opposite directions.

Cut the corner angles for a 45 degree miter joint on the inside corner joint. For inside corners, move the miter saw to your left until it is at the 45 degree mark. Bring the cove molding in from the left and place just enough of the molding under the saw with the intention of making a completed 45 degree angle cut and cut down a few inches on the right side of the piece of cove molding. Fix the cove molding firmly in place while you do this. Adjust the saw just the opposite way for the other piece and repeat the process accordingly.

Cut the corner angle for a 45 degree miter joint on the outside corner joint. This, however becomes a little more difficult since the miter saw does not reflect the actual angle, in fact, each cut is exactly the opposite of the cut you actually want to make. For outside corners, follow the same steps that you carried out in order to cut the inside corners.

Incoming search terms:

  • crown molding
  • crown moulding
  • how to cut Cove molding
  • cutting cove molding
  • best cove cutting tool
  • how to cut cove molding corners
  • cutting molding angles ceiling
  • crown molding under a cove
  • cove mold cuts wall ceiling
  • cove modling angles